www.clare.com ds-cpc1020n-r02 1 cpc1020n single-pole, normally open 4-lead sop optomos ? relay rohs 2002/95/ec e 3 pb part # description cpc1020n 4-lead sop (100/tube) CPC1020NTR 4-lead sop (2000/reel) parameter rating units blocking voltage 30 v p load current 1.2 a dc on-resistance, max 0.25 applications features description ordering information pin configuration ? sensor circuitry ? instrumentation ? multiplexers ? data acquisition ? electronic switching ? i/o subsystems ? meters (watt-hour, water, gas) ? medical equipment?patient/equipment isolation ? aerospace ? industrial controls ? 1500v rms input/output isolation ? small 4-lead sop package ? low drive power requirements (ttl/cmos compatible) ? no moving parts ? high reliability ? arc-free with no snubbing circuits ? no emi/rfi generation ? machine insertable, wave solderable ? tape & reel version available the cpc1020n is a 30v, single-pole, normally open (1-form-a) solid state relay. the ultra-low on-resistance, 0.25 , of this relay allows for high-current operation. clare's patented optomos architecture makes available the optically coupled technology necessary to activate the output's efficient mosfet switches while providing 1500v rms input to output isolation. control of the isolated output is accomplished by means of the highly effective gaalas infrared led at the input. approvals ? ul recognized component: file e76270 ? csa certified component: certificate 1175739 ? en/iec 60950-1 certified component: tuv certificate b 09 07 49410 004 switching characteristics of normally open devices form-a i f i load 10% 90% t on t off 1 2 3 4 + control C control load load
www.clare.com 2 r02 cpc1020n absolute maximum ratings are stress ratings. stresses in excess of these ratings can cause permanent damage to the device. functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. absolute maximum ratings @ 25oc parameter ratings units blocking voltage 30 v p input power dissipation 1 75 mw input control current 50 ma peak (10ms) 1 a reverse input voltage 5 v total power dissipation 2 400 mw isolation voltage, input to output 1500 v rms operational temperature -40 to +85 c storage temperature -40 to +125 c 1 derate linearly 1.33 mw / oc 2 derate linearly 3.33 mw / oc parameter conditions symbol min typ max units output characteristics load current continuous 1 i f =2ma i l - - 1.2 a dc peak t < 10ms i lpk --3a on-resistance 2 i l =1a r on - 0.116 0.25 off-state leakage current v l =30v p i leak --1 a switching speeds turn-on i f =5ma, v l =10v t on - 0.48 3 ms turn-off t off - 0.65 3 output capacitance v l =15v, f=1mhz c out -70 -pf input characteristics input control current i l =1a i f - 0.13 2 ma input dropout current - i f 0.1 - - ma input voltage drop i f =5ma v f 0.9 1.2 1.4 v reverse input current v r =5v i r - - 10 a input/output characteristics capacitance, input to output - c i/o -3 -pf 1 load current derates linearly from 1.2a @ 25 o c to 0.58a @85 o c. 2 measurement taken within 1 second of on-time. electrical characteristics @ 25oc esd rating (human body model) 1000 volts esd rating
cpc1020n www.clare.com 3 r02 performance data* *the performance data shown in the graphs above is typical of device performance. for guaranteed parameters not indicated in t he written speci? cations, please contact our application department. turn-on time (ms) 0.35 0.40 0.45 0.50 0.55 0.60 device count (n) 0 5 10 15 20 25 typical turn-on time distribution (n=50, i f =5ma, i l =5ma, t a =25oc) turn-off time (ms) 0.47 0.55 0.63 0.71 0.79 device count (n) 0 5 10 15 20 25 30 typical turn-off time distribution (n=50, i f =5ma, i l =5ma, t a =25oc) on-resistance ( ) 0.113 0.114 0.115 0.116 0.117 0.118 device count (n) 0 5 10 15 20 typical on-resistance distribution (n=50, i f =2ma, i l =1a, t a =25oc) led forward current (ma) 0.093 0.101 0.109 0.117 0.125 0.133 device count (n) 0 5 10 15 20 25 typical i f for switch operation (n=50, i l =100ma, t a =25oc) blocking voltage (v p ) 37.8 38.2 38.6 39.0 39.4 device count (n) 0 5 10 15 20 25 typical blocking voltage distribution (n=50, t a =25oc) led forward voltage (v) 1.25 1.26 1.27 1.28 1.29 device count (n) 0 5 10 15 20 25 30 35 typical led forward voltage drop (n=50, i f =5ma, t a =25oc) temperature (oc) -40 -20 0 20 40 60 80 100 led forward voltage (v) 1.0 1.1 1.2 1.3 1.4 1.5 1.6 typical led forward voltage drop vs. temperature i f =2ma i f =5ma i f =50ma i f =20ma i f =10ma led forward current (ma) 0 1020304050 turn on time (ms) 0 0.5 1.0 1.5 2.0 2.5 typical turn-on time vs. led forward current (i l =100ma) led forward current (ma) 0 1020304050 turn-off time ( s) 600 620 640 660 680 700 typical turn-off time vs. led forward current (i l =100ma) temperature (oc) -40 -20 0 20 40 60 80 100 led forward current (ma) 0.08 0.10 0.12 0.14 0.16 0.18 0.20 typical i f for switch operation vs. temperature (i l =1a) temperature (oc) -40 -20 0 20 40 60 80 100 turn-on time (ms) 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 typical turn-on time vs. temperature (i l =100ma) i f =2ma i f =5ma temperature (oc) -40 -20 0 20 40 60 80 100 turn-off time (ms) 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 typical turn-off time vs. temperature (i l =100ma) i f =2ma i f =5ma
www.clare.com 4 r02 cpc1020n performance data* *the performance data shown in the graphs above is typical of device performance. for guaranteed parameters not indicated in t he written speci? cations, please contact our application department. load voltage (v) -0.20 -0.15 -0.10 -0.05 0.00 0.05 0.10 0.15 0.20 load current (a) -1.5 -1.0 -0.5 0.0 0.5 1.0 1.5 typical load voltage vs. load current (i f =2ma, t a =25oc) temperature (oc) -40 -20 0 20 40 60 80 100 on-resistance ( ) 0.10 0.15 0.20 0.25 0.30 0.35 0.40 typical on-resistance vs. temperature (i f =2ma, i l =0.5a) temperature (oc) -40 -20 0 20 40 60 80 100 load current (a dc ) 0.0 0.3 0.5 0.8 1.0 1.3 1.5 typical load current vs. temperature (i f =2ma) temperature (oc) -40 -20 0 20 40 60 80 100 blocking voltage (v p ) 36.5 37.0 37.5 38.0 38.5 39.0 39.5 40.0 40.5 typical blocking voltage vs. temperature (i l =1 a) temperature (oc) -40 -20 0 20 40 60 80 100 leakage current (na) 0 20 40 60 80 100 typical leakage current vs. temperature measured across pins 3&4 (i f =0ma, v l =30v) time 10 s 100 s 1ms 10ms 100ms 1s 10s 100s current (a) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 energy rating curve
cpc1020n www.clare.com 5 r02 manufacturing information moisture sensitivity all plastic encapsulated semiconductor packages are susceptible to moisture ingression. clare classified all of its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, ipc/jedec j-std-020 , in force at the time of product evaluation. we test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. this product carries a moisture sensitivity level (msl) rating as shown below, and should be handled according to the requirements of the latest version of the joint industry standard ipc/jedec j-std-033 . device moisture sensitivity level (msl) rating cpc1020n msl 3 esd sensitivity this product is esd sensitive , and should be handled according to the industry standard jesd-625 . reflow profile this product has a maximum body temperature and time rating as shown below. all other guidelines of j-std-020 must be observed. device maximum temperature x time cpc1020n 260oc for 30 seconds board wash clare recommends the use of no-clean flux formulations. however, board washing to remove flux residue is acceptable. since clare employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. chlorine- or fluorine-based solvents or fluxes should not be used. cleaning methods that employ ultrasonic energy should not be used. rohs 2002/95/ec e 3 pb
clare, inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publica tion and reserves the right to make changes to specifications and product descriptions at any time without notice. neither circuit patent licenses nor indemnity are expressed or implied. except as set forth in clare?s standard terms and conditions of sale, clare, inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products incl uding, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. the products described in this document are not designed, intended, authorized or warranted for use as components in systems in tended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of clare?s product may result in direct physical harm, i njury, or death to a person or severe property or environmental damage. clare, inc. reserves the right to discontinue or make changes to its products at any time without notice. specification: ds-cpc1020n-r02 ?copyright 2010, clare, inc. optomos? is a registered trademark of clare, inc. all rights reserved. printed in usa. 8/27/2010 for additional information please visit our website at: www.clare.com 6 cpc1020n dimensions mm (inches) note: all dimensional tolerances per standard eia-481-2 except as noted embossment embossed carrier 330.2 dia (13.00 dia) top cover tape thickness 0.102 max (0.004 max) user direction o f fee d user direction of feed k 0 =2.70 (0.106) k 1 =2.30 (0.091) b 0 =4.70 (0.185) w=12.00 (0.472) p=8.00 (0.315) a 0 =6.50 (0.256) mechanical dimensions recommended pcb land pattern 2.54 (0.10) 5.60 (0.2205) 1.30 (0.0512) 0.60 (0.0217) dimensions mm (inches) pin 1 4.089 0.203 (0.161 0.008) 2.54 typ (0.100 typ) 6.096 0.102 (0.240 0.004) 3.810 0.076 (0.150 0.003) 0.432 0.127 (0.017 0.005) 0.200 0.025 (0.008 0.001) 1.02 0.025 (0.040 0.001) 2.184 max (0.086 max) 0.381 typ. (0.015 typ.) lead to package standoff: min: 0.0254 (0.001) max: 0.102 (0.004) 0.762 0.102 (0.030 0.004) cpc1020n cpc1020n tape & reel
|
